Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> Large capacity SGMVV type servo motor
>> SGMVV-2BDDD2D Large capacity servo motor
SGMVV-2BDDD2D Large capacity servo motor
Yaskawa SGMVV-2BDDD2D Product information and technical parameters：
Brand: Yaskawa
Name: Large capacity servo motor
Model: SGMVV-2BDDD2D
Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 800r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.2kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified SGMVV-2BDDD2D.
No need to write parameters in the device assembly site, can reduce the equipment delivery time SGMVV-2BDDD2D
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed SGMVV-2BDDD2D.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdownLarge capacity SGMVV type servo motor SGMVV-2BDDD2D.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -V series servo motor SGMJV.
Rated output: 0.6kw (600W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Insstallation method: flange type SGMVV-2BDDD2D.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGMVV-2BDDD2D.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.
Maximum applicable motor capacity: 0.2kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware options: paint.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified SGMVV-2BDDD2D.
No need to write parameters in the device assembly site, can reduce the equipment delivery time SGMVV-2BDDD2D
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed SGMVV-2BDDD2D.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdownLarge capacity SGMVV type servo motor SGMVV-2BDDD2D.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -V series servo motor SGMJV.
Rated output: 0.6kw (600W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Insstallation method: flange type SGMVV-2BDDD2D.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGMVV-2BDDD2D.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.
...More relevant models >>>>
Last one: Yaskawa Large capacity servo motor SGMVV-2BDDD2C
next one: Yaskawa Large capacity servo motor SGMVV-2BDDD2E
Related download