Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> Large capacity SGMVV type servo motor
>> SGMVV-2BA3DLG Large capacity servo motor
SGMVV-2BA3DLG Large capacity servo motor
Yaskawa SGMVV-2BA3DLG Product information and technical parameters：
Brand: Yaskawa
Name: Large capacity servo motor
Model: SGMVV-2BA3DLG
Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: keep the brake (DC24V), with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
Sigma -V series servo motor SGMPS.
Rated output: 1.5kw.
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive SGMVV-2BA3DLG.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1 SGMVV-2BA3DLG5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C SGMVV-2BA3DLG.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLow inertia, high speed servo motor type SGM7A (rated speed 3000r\/min) SGMVV-2BA3DLG.
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse).
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problemServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 7.5Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMVV-2BA3DLG.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMVV-2BA3DLG.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Rated output: 1.5kw.
Power supply voltage: AC200V.
Serial encoder: 17 bit absolute value type (standard).
Design sequence: IP55 (standard).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Corresponding to the RoHS instruction: in accordance with the RoHS directive SGMVV-2BA3DLG.
Medium inertia
Flat type deep short
Equipped with high resolution serial encoder (17 bit)
Max speed up to 6000r\/min
Variety is complete (100W ~ 1 SGMVV-2BA3DLG5kW, with hold brake)
Standard using IP55. Also applies to IP67 (optional).
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C SGMVV-2BA3DLG.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLow inertia, high speed servo motor type SGM7A (rated speed 3000r\/min) SGMVV-2BA3DLG.
Rated output: 50W.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse).
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problemServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 7.5Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMVV-2BA3DLG.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMVV-2BA3DLG.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>
Last one: Yaskawa Large capacity servo motor SGMVV-3GA3DLF
next one: Yaskawa Large capacity servo motor SGMVV-3ZA3DLG
Related download