Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMSV type motor
>> SGMSV-30D3A6D servo motor
SGMSV-30D3A6D servo motor
Yaskawa SGMSV-30D3A6D Manual And Instructions
SGMSV-30D3A6D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-30D3A6D Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-30D3A6D
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMSV-30D3A6D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-30D3A6D Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-30D3A6D
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Optional (hardware): DB resistance external type.
Excellent mechanical properties, do the best in the master!
Easy and efficient work, is no longer a dream,
Sigma -v series servo drive, you can make your dreams come true SGMSV-30D3A6D SGMSV-30D3A6D
Sigma -v series is equipped with new free adjustment function,
Broke the common sense of the servo drive "can''t run smoothly without adjusting",
To achieve a pass that is to use.
A new type of advanced automatic tuning function Sigma -v series,
The installation time can be shortened, and the performance of the machine can be fully played SGMSV-30D3A6D. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 5kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMSV-30D3A6D.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
It is helpful to the servo performance of ultra high speed and ultra precision control SGMSV-30D3A6D.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suuppression function SGMSV-30D3A6D.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth drive
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Optional (hardware): DB resistance external type.
Excellent mechanical properties, do the best in the master!
Easy and efficient work, is no longer a dream,
Sigma -v series servo drive, you can make your dreams come true SGMSV-30D3A6D SGMSV-30D3A6D
Sigma -v series is equipped with new free adjustment function,
Broke the common sense of the servo drive "can''t run smoothly without adjusting",
To achieve a pass that is to use.
A new type of advanced automatic tuning function Sigma -v series,
The installation time can be shortened, and the performance of the machine can be fully played SGMSV-30D3A6D. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 5kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGMSV-30D3A6D.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
It is helpful to the servo performance of ultra high speed and ultra precision control SGMSV-30D3A6D.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suuppression function SGMSV-30D3A6D.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth drive
...More relevant models >>>>
Last one: 
next one: Related download