Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDM series
>> SGMPH type motor
>> SGMPH-08ABA4E Servo motor
SGMPH-08ABA4E Servo motor
Yaskawa SGMPH-08ABA4E Product information and technical parameters：
Brand: Yaskawa
Name: Servo motor
Model: SGMPH-08ABA4E
Servo motor type SGMPH (speed: 3000r/min).
Power: 0.75kw.
Power supply voltage: three phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: with oil seal, DC24V brake.
Partial flat series: the need to install the servo motor in a small space.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated.
Large capacity SGMVV type servo motor.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC24V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMPH-08ABA4E SGMPH-08ABA4E
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGMPH-08ABA4E.
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): base mounting type (standard).
With the latest technology to pursue the use of convenience SGMPH-08ABA4E.
The use of new non adjustment function, no need to adjust.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed.
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start.
Excellent mechanical properties, do the best in the master!
Easy and efficient work, is no longer a dream,
Sigma -v series servo drive, you can make your dreams come true.
Sigma -v series is equipped with new free adjustment function,
Broke the common sense of the servo drive "can''t run smoothly without adjusting",
To achieve a pass that is to use.
A new type of advanced automaticc tuning function Sigma -v series,
The installation time can be shortened, and the performance of the machine can be fully played SGMPH-08ABA4E.
Achieve a high response 1kHz above.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control SGMPH-08ABA4E.
Rated output: 37KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC24V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMPH-08ABA4E SGMPH-08ABA4E
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGMPH-08ABA4E.
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Matching (hardware): base mounting type (standard).
With the latest technology to pursue the use of convenience SGMPH-08ABA4E.
The use of new non adjustment function, no need to adjust.
The vibration suppression function is also strengthened, and the load fluctuation can be effectively suppressed.
Greatly shorten the setting time.
Using engineering tool SigmaWin+ to set the guide function and the distribution confirmation function,
Can look at the picture simply to complete the start.
Excellent mechanical properties, do the best in the master!
Easy and efficient work, is no longer a dream,
Sigma -v series servo drive, you can make your dreams come true.
Sigma -v series is equipped with new free adjustment function,
Broke the common sense of the servo drive "can''t run smoothly without adjusting",
To achieve a pass that is to use.
A new type of advanced automaticc tuning function Sigma -v series,
The installation time can be shortened, and the performance of the machine can be fully played SGMPH-08ABA4E.
Achieve a high response 1kHz above.
Equipped with a new advanced automatic tuning function.
Through the model tracking control, the positioning time is shortened,
And through the vibration suppression function, easy to achieve a smooth mechanical control SGMPH-08ABA4E.
...More relevant models >>>>
Last one: 
next one: Related download