Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMGV type motor
>> SGMGV-20DDC6E Rotary servo motor
SGMGV-20DDC6E Rotary servo motor
Yaskawa SGMGV-20DDC6E Manual And Instructions
SGMGV-20DDC6E Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMGV-20DDC6E Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-20DDC6E
Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMGV-20DDC6E Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMGV-20DDC6E Product information and technical parameters：
Brand: Yaskawa
Name: Rotary servo motor
Model: SGMGV-20DDC6E
Sigma -V series servo motor SGMGV.
Rated output: 1.8kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Dual axis servo drive SGD7W.
Maximum applicable motor capacity: 0.75kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Japanese production, interface is HMI connector).
Design sequence: A.
Hardware options: paint.
Dual axis servo unit (200W x 2 axis to 1kW x 2 axis) SGMGV-20DDC6E.
Speed frequency response 1.6kHz.
Enhanced vibration suppression SGMGV-20DDC6E
Gain adjustment without servo
YASKAWA created the "free adjustment function", the maximum load at 30 times the action does not produce vibration.
In addition, even if the action is changed, the action is stable.
Can be used in harsh environment and energy saving servo.
Can successfully build the best system in the worldLarge capacity servo unit SGMGV-20DDC6E.
Maximum applicable motor capacity: 55KW.
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control SGMGV-20DDC6E. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical propertties SGMGV-20DDC6E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGMGV-20DDC6E.
Maximum applicable motor capacity: 0.75kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Japanese production, interface is HMI connector).
Design sequence: A.
Hardware options: paint.
Dual axis servo unit (200W x 2 axis to 1kW x 2 axis) SGMGV-20DDC6E.
Speed frequency response 1.6kHz.
Enhanced vibration suppression SGMGV-20DDC6E
Gain adjustment without servo
YASKAWA created the "free adjustment function", the maximum load at 30 times the action does not produce vibration.
In addition, even if the action is changed, the action is stable.
Can be used in harsh environment and energy saving servo.
Can successfully build the best system in the worldLarge capacity servo unit SGMGV-20DDC6E.
Maximum applicable motor capacity: 55KW.
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control SGMGV-20DDC6E. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r/min.
The main mechanical structure: support mounting type, straight shaft (no keyway and screw).
Optional parts: with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical propertties SGMGV-20DDC6E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGMGV-20DDC6E.
...More relevant models >>>>
Last one: Yaskawa Rotary servo motor SGMGV-13DDC6E
next one: Yaskawa Rotary servo motor SGMGV-30DDC6E
Related download