Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDM series
>> SGMGH type servo motor
>> SGMGH-75A2A6S servo motor
SGMGH-75A2A6S servo motor
Yaskawa SGMGH-75A2A6S Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMGH-75A2A6S
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 7.5Kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGH-75A2A6S.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products SGMGH-75A2A6S
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGMGH-75A2A6S.
Servo driver SGD7S.
Maximum applicable motor capacity: 0.2kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-II communication command type.
Design sequence: A.
Hardware options: paint.
Performance excellence.
The performance and speed of the device can be improved.
Upgrade free adjustment function.
Without adjusting the operation, no vibration can be achieved SGMGH-75A2A6S.
To ensure that the procedures and parameters of the previous product compatibility.
After replacement of the product, can easily improve the performance of the device.
Sigma -7 series has rich models and related products.
Customers can easily build the system.
From selection to maintenance, rich service content.
Especially when the servo system is in trouble,
Can immediately grasp the product information in the field.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problemFull closed loop module.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMGH-75A2A6S.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response SGMGH-75A2A6S.
External encoder capable of corresponding high resolution (linear grating).
Rated output: 22KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with dust.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGH-75A2A6S.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products SGMGH-75A2A6S
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGMGH-75A2A6S.
Servo driver SGD7S.
Maximum applicable motor capacity: 0.2kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-II communication command type.
Design sequence: A.
Hardware options: paint.
Performance excellence.
The performance and speed of the device can be improved.
Upgrade free adjustment function.
Without adjusting the operation, no vibration can be achieved SGMGH-75A2A6S.
To ensure that the procedures and parameters of the previous product compatibility.
After replacement of the product, can easily improve the performance of the device.
Sigma -7 series has rich models and related products.
Customers can easily build the system.
From selection to maintenance, rich service content.
Especially when the servo system is in trouble,
Can immediately grasp the product information in the field.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problemFull closed loop module.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware specifications: paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional modules: full closed loop module SGMGH-75A2A6S.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed onn the side of the machine to realize the high precision and high response SGMGH-75A2A6S.
External encoder capable of corresponding high resolution (linear grating).
...More relevant models >>>>
Last one: 
next one: Related download