Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDM series
>> SGMGH type servo motor
>> SGMGH-30ACC31 Motor for high precision machine tool
SGMGH-30ACC31 Motor for high precision machine tool
Yaskawa SGMGH-30ACC31 Product information and technical parameters：
Brand: Yaskawa
Name: Motor for high precision machine tool
Model: SGMGH-30ACC31
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 2.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Servo motor type SGMPH (speed: 3000r/min).
Power: 0.2kw.
Power supply voltage: single phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: with DC90V brake.
Partial flat series: the need to install the servo motor in a small space SGMGH-30ACC31.
Flexible user system.
For you to build the best system to enrich the product line to support you SGMGH-30ACC31
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGMGH-30ACC31. Single axis servo driver SGD7S.
Maximum applicable motor capacity: 5.0kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware purchase: rack installation specifications SGMGH-30ACC31.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suppression function.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth driveSigma -V series servo motor SGMGV.
Rated output: 7.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMGH-30ACC31.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-30ACC31.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Power: 0.2kw.
Power supply voltage: single phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft with key.
Optional parts: with DC90V brake.
Partial flat series: the need to install the servo motor in a small space SGMGH-30ACC31.
Flexible user system.
For you to build the best system to enrich the product line to support you SGMGH-30ACC31
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operated SGMGH-30ACC31. Single axis servo driver SGD7S.
Maximum applicable motor capacity: 5.0kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware purchase: rack installation specifications SGMGH-30ACC31.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suppression function.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth driveSigma -V series servo motor SGMGV.
Rated output: 7.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: no matching.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMGH-30ACC31.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGH-30ACC31.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Last one: Yaskawa Motor for high precision machine tool SGMGH-20ACC31
next one: Yaskawa Motor for high precision machine tool SGMGH-44ACC31
Related download