Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> Large capacity SGMVV type servo motor
>> SGMCV-14BEA15 Direct drive servo motor
SGMCV-14BEA15 Direct drive servo motor
Yaskawa SGMCV-14BEA15 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCV-14BEA15
Direct drive type servo motor SGMCV type.
Rated torque: M \/ 14N.
Servo motor diameter: diameter of 135mm.
Serial encoder: 22 bit (single cycle absolute encoder).
Design sequence: A.
Flange: reverse load side.
Optional parts: high mechanical precision (axis offset, offset 0.01mm).
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 12 ~ 75N \/ m, maximum speed: 500 ~ 600r\/min).
By using 22 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing apparatus.
Liquid crystal circuit board manufacturing device.
Various inspection and test equipment.
Electronic component packaging machine.
C information processor.
C inspection equipment.
A variety of automated machinery.
Manipulator
Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMCV-14BEA15 SGMCV-14BEA15
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenHigh performance, use the best type of servo unit (purpose type) SGMCV-14BEA15.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Function: pressure feedback control function SGMCV-14BEA15.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller. Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMCV-14BEA15.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMCV-14BEA15.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 800r\/min.
The main mechanical structure: support mounting type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMCV-14BEA15 SGMCV-14BEA15
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenHigh performance, use the best type of servo unit (purpose type) SGMCV-14BEA15.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: B.
Hardware specification: base mounting type (standard).
Function: pressure feedback control function SGMCV-14BEA15.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller. Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
HHeat resistance grade: F SGMCV-14BEA15.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMCV-14BEA15.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Last one: Yaskawa Direct drive servo motor SGMCV-10BEA15
next one: Yaskawa Direct drive servo motor SGMCV-17BEA15
Related download