Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMCS type direct drive motor
>> SGMCS-17NDA31 Direct drive servo motor
SGMCS-17NDA31 Direct drive servo motor
Yaskawa SGMCS-17NDA31 Manual And Instructions
SGMCS-17NDA31 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-17NDA31 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-17NDA31
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 17N.
Servo motor outside diameter size: 360mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMCS-17NDA31 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-17NDA31 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-17NDA31
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 17N.
Servo motor outside diameter size: 360mm.
Serial encoder: 20 bit Delta (optional).
Design sequence: the outer diameter size of the servo motor is marked as N and M.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Sigma -V series servo motor SGMSV.
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Super power rate.
Variety is complete (1.0kW ~ 7 SGMCS-17NDA31. 0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7 SGMCS-17NDA310kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type SGMCS-17NDA31.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationHigh performance, use the best type of servo unit (purpose type) SGMCS-17NDA31.
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Function: to support the use of rotary table.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMCS-17NDA31.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMCS-17NDA31.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: no matching.
Super power rate.
Variety is complete (1.0kW ~ 7 SGMCS-17NDA31. 0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7 SGMCS-17NDA310kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type SGMCS-17NDA31.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationHigh performance, use the best type of servo unit (purpose type) SGMCS-17NDA31.
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC100V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specifications: paint.
Function: to support the use of rotary table.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rootation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGMCS-17NDA31.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGMCS-17NDA31.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.
...More relevant models >>>>
Last one: Yaskawa Direct drive servo motor SGMCS-16NDA31
next one: Yaskawa Direct drive servo motor SGMCS-25NDA31
Related download