Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMCS type direct drive motor
>> SGMCS-08B3C11 Direct drive servo motor
SGMCS-08B3C11 Direct drive servo motor
Yaskawa SGMCS-08B3C11 Manual And Instructions
SGMCS-08B3C11 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-08B3C11 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-08B3C11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 8.0N.
Servo motor outside diameter size: 135mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter of the servo motor is marked as B, C and D.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMCS-08B3C11 Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMCS-08B3C11 Product information and technical parameters：
Brand: Yaskawa
Name: Direct drive servo motor
Model: SGMCS-08B3C11
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 8.0N.
Servo motor outside diameter size: 135mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter of the servo motor is marked as B, C and D.
Flange specification: face C, reverse load side.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-08B3C11 SGMCS-08B3C11
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlLarge capacity SGMVV type servo motor SGMCS-08B3C11.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMCS-08B3C11.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen.
Servo motor type SGMAH (speed: 3000r\/min).
Power: 0.1kw.
Power supply voltage: single phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting aand maintenance time is shortened SGMCS-08B3C11.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanicall characteristics SGMCS-08B3C11.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMCS-08B3C11 SGMCS-08B3C11
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlLarge capacity SGMVV type servo motor SGMCS-08B3C11.
Rated output: 30KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMCS-08B3C11.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen.
Servo motor type SGMAH (speed: 3000r\/min).
Power: 0.1kw.
Power supply voltage: single phase AC200V.
Serial encoder: 13 bit relative value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal.
Improve mechanical properties.
In order to achieve a higher production efficiency, SGDMAH type to the best control to explore the highest performance of the machine,
Compared with the original models, CPU computing time for its 1\/2, through the expansion of the new control algorithm,
Positioning time is shortened to the original product of 1\/3, to achieve a good response.
The parameter setting aand maintenance time is shortened SGMCS-08B3C11.
In order to establish a high degree system in a short time, the use of the simplicity of the.
Flexible use of online automatic adjustment function,
Automatic adjustment of servo system with mechanicall characteristics SGMCS-08B3C11.
Then use the main loop \/ control circuit power separation and alarm tracking memory function, can be simple to carry out maintenance
...More relevant models >>>>
Last one: Yaskawa Direct drive servo motor SGMCS-07B3C11
next one: Yaskawa Direct drive servo motor SGMCS-10B3C11
Related download