Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMAV type motor
>> SGMAV-C2ADA6E Ultra low inertia servo motor
SGMAV-C2ADA6E Ultra low inertia servo motor
Yaskawa SGMAV-C2ADA6E Manual And Instructions
SGMAV-C2ADA6E Setup Rotational MotorCommand Manual
Yaskawa SGMAV-C2ADA6E Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-C2ADA6E
Sigma -V series servo motor SGMAV.
Rated output: 0.15kw (150W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMAV-C2ADA6E Setup Rotational MotorCommand Manual
Yaskawa SGMAV-C2ADA6E Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-C2ADA6E
Sigma -V series servo motor SGMAV.
Rated output: 0.15kw (150W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Equipped with INDEXER functional type servo unit (kit type).
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (rotary type servo motor).
Matching (hardware): shelf installation type + paint.
Matching (software): standard SGMAV-C2ADA6E.
Matching (parameter): standard.
Optional modules: INDEXER module.
Simple.
By programming and serial programming, easy implementation of motion control SGMAV-C2ADA6E
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table SGMAV-C2ADA6E.
The maximum number of programmable positioning points to 256 points.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller SGMAV-C2ADA6E. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMAV-C2ADA6E.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMAV-C2ADA6E.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC200V.
Interface: instruction selection and installation (rotary type servo motor).
Matching (hardware): shelf installation type + paint.
Matching (software): standard SGMAV-C2ADA6E.
Matching (parameter): standard.
Optional modules: INDEXER module.
Simple.
By programming and serial programming, easy implementation of motion control SGMAV-C2ADA6E
Can also be installed through the Windows environment support tool (SigmaWin+) easy to start.
The I/O module can be connected with the upper controller simply.
Smart.
To support the operation of the main purpose of the positioning operation based on the program table SGMAV-C2ADA6E.
The maximum number of programmable positioning points to 256 points.
With external positioning, JOG speed table operation, the origin of reversion, rich features such as programmable signal output.
I/O points for the input: 19 points, output: 16 points.
Speedy.
High speed and high precision positioning by combining with high performance V series.
Motion control can be realized without using motion controller SGMAV-C2ADA6E. Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.4kw.
Power supply voltage: single phase AC100V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMAV-C2ADA6E.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMAV-C2ADA6E.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Last one: Yaskawa Ultra low inertia servo motor SGMAV-01ADA6E
next one: Yaskawa Ultra low inertia servo motor SGMAV-02ADA6E
Related download