Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMAV type motor
>> SGMAV-01ADABC Ultra low inertia servo motor
SGMAV-01ADABC Ultra low inertia servo motor
Yaskawa SGMAV-01ADABC Manual And Instructions
SGMAV-01ADABC Setup Rotational MotorCommand Manual
Yaskawa SGMAV-01ADABC Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-01ADABC
Sigma -V series servo motor SGMAV.
Rated output: 0.1kw (100W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with hold brake (DC24V).
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMAV-01ADABC Setup Rotational MotorCommand Manual
Yaskawa SGMAV-01ADABC Product information and technical parameters：
Brand: Yaskawa
Name: Ultra low inertia servo motor
Model: SGMAV-01ADABC
Sigma -V series servo motor SGMAV.
Rated output: 0.1kw (100W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with hold brake (DC24V).
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%).
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load SGMAV-01ADABC.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMAV-01ADABC
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMGH type SGMAV-01ADABC.
Rated speed: 1000r\/min.
Power: 1.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMAV-01ADABC.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlLarge capacity servo unit.
Maximum applicable motor capacity: 37KW.
Power supply voltage: three phase AC400V.
Fastening: MECHATROLINK-III communication command type (rotary servo motor).
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMAV-01ADABC.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMAV-01ADABC.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Rated speed: 1500r\/min.
Power: 5.5kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load SGMAV-01ADABC.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMAV-01ADABC
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMGH type SGMAV-01ADABC.
Rated speed: 1000r\/min.
Power: 1.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: no brake oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMAV-01ADABC.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlLarge capacity servo unit.
Maximum applicable motor capacity: 37KW.
Power supply voltage: three phase AC400V.
Fastening: MECHATROLINK-III communication command type (rotary servo motor).
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMAV-01ADABC.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGMAV-01ADABC.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>
Last one: Yaskawa Ultra low inertia servo motor SGMAV-A5ADABC
next one: Yaskawa Ultra low inertia servo motor SGMAV-C2ADABC
Related download