Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGDV-____15 Type (Used by linear servo motor)
>> SGDV-R90F15A Servo driver for linear servo motor
SGDV-R90F15A Servo driver for linear servo motor
Yaskawa SGDV-R90F15A Manual And Instructions
SGDV-R90F15A MECHATROLINK-II CommandsUSER'S MANUAL
SGDV-R90F15A Design and MaintenanceUSER'S MANUAL
Yaskawa SGDV-R90F15A Product information and technical parameters：
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-R90F15A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: single phase AC100V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
SGDV-R90F15A MECHATROLINK-II CommandsUSER'S MANUAL
SGDV-R90F15A Design and MaintenanceUSER'S MANUAL
Yaskawa SGDV-R90F15A Product information and technical parameters：
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-R90F15A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: single phase AC100V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Direct drive type servo motor SGMCV type.
Rated torque: M \/ 8.0N.
Servo motor diameter: diameter of 135mm.
Serial encoder: 22 bit (multi ring absolute encoder).
Design sequence: A.
Flange: reverse load side.
Optional parts: high mechanical precision (axis offset, offset 0.01mm).
Under the condition of no speed reducer, the load is directly driven SGDV-R90F15A.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 12 ~ 75N \/ m, maximum speed: 500 ~ 600r\/min) SGDV-R90F15A
By using 22 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing apparatus.
Liquid crystal circuit board manufacturing device SGDV-R90F15A.
Various inspection and test equipment.
Electronic component packaging machine.
C information processor.
C inspection equipment.
A variety of automated machinery.
ManipulatorServo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 2.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key SGDV-R90F15A.
Optional parts: with oil seal, D24V brake.
Partial flat series: the need to install the servo motor in a small space.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorSigma -V series servo motor SGMSV.
Rated output: 5.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F SGDV-R90F15A.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDV-R90F15A.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Rated torque: M \/ 8.0N.
Servo motor diameter: diameter of 135mm.
Serial encoder: 22 bit (multi ring absolute encoder).
Design sequence: A.
Flange: reverse load side.
Optional parts: high mechanical precision (axis offset, offset 0.01mm).
Under the condition of no speed reducer, the load is directly driven SGDV-R90F15A.
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 12 ~ 75N \/ m, maximum speed: 500 ~ 600r\/min) SGDV-R90F15A
By using 22 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping.
Use example:
Semiconductor manufacturing apparatus.
Liquid crystal circuit board manufacturing device SGDV-R90F15A.
Various inspection and test equipment.
Electronic component packaging machine.
C information processor.
C inspection equipment.
A variety of automated machinery.
ManipulatorServo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 2.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key SGDV-R90F15A.
Optional parts: with oil seal, D24V brake.
Partial flat series: the need to install the servo motor in a small space.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorSigma -V series servo motor SGMSV.
Rated output: 5.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F SGDV-R90F15A.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDV-R90F15A.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
Last one: Yaskawa Servo driver for linear servo motor SGDV-R70F15B002000
next one: Yaskawa Servo driver for linear servo motor SGDV-R90F15A002000
Related download