YASKAWA
Home >> Products >> Yaskawa >> Servo driver / motor >> SGDV type >> SGDV-____15 Type (Used by linear servo motor) >> SGDV-210D15B002000 Servo driver for linear servo motor

SGDV-210D15B002000 Servo driver for linear servo motor

Yaskawa SGDV-210D15B002000 Manual And Instructions
SGDV-210D15B002000 MECHATROLINK-II CommandsUSER'S MANUAL
SGDV-210D15B002000 Design and MaintenanceUSER'S MANUAL

Yaskawa SGDV-210D15B002000 Product information and technical parameters:
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-210D15B002000
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 6kw.
Power supply voltage: three phase AC400V.
Design sequence: B type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 4.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
Ultra high power response series: the need for small inertia, high torque SGDV-210D15B002000.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain SGDV-210D15B002000
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals SGDV-210D15B002000.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistorSigma -V series servo motor SGMSV.
Rated output: 2.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC90V).
Super power rate.
Variety is complete (1 SGDV-210D15B002000. 0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationSigma -7 series servo unit SGD7S.
Maximum applicable motor capacity: 6.0kW.
Voltage: three phase AC200V.
Interface: analog voltage, pulse sequence.
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Select servo.
Since the Yaskawa since the beginning of 1992 sales of sigma series, has always attached great importance to technical exchanges and customer,
In order to solve the new problem of customer machinery, and repeatedly to carry out technical innovation.
High speed, high accuracy, the use of convenience in recent years has beenn the requirement of customers,
But the degree of its requirement is continuously deepening SGDV-210D15B002000.
2014, the servo drive upgrade to have 7 major advantages",
Provide solutions for customers unique yaskawa.
With its excellent performancee, convenient operation, long life cycle, etc SGDV-210D15B002000. ,
In all these areas will have great potential, provides solutions to the shocking. "Choose servo, choose"


...More relevant models >>>>