SGDV-1R9D25A Servo driver for linear servo motor

YaskawaServo driver for linear servo motorSGDV-1R9D25A

SGDV-1R9D25A Introduce | SGDV-1R9D25A Catalog / Manual / Instructions / Software download

Yaskawa SGDV-1R9D25A Product information and technical parameters：
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-1R9D25A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: with hold brake (DC24V).
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGDV-1R9D25A SGDV-1R9D25A
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenServo motor type SGMPH (speed: 3000r\/min) SGDV-1R9D25A.
Power: 0.4kw.
Power supply voltage: single phase AC200V.
Serial encoder: 16 bit relative value.
Design sequence: Waterproof standard IP67.
Shaft end: straight shaft with key.
Optional parts: with oil seal, DC24V brake.
Partial flat series: the need to install the servo motor in a small space SGDV-1R9D25A.
Flexible user system.
For you to build the best system to enrich the product line to support you.
Products with single phase 200V, single phase 100V, three-phase 200V,
And for the absolute value encoder, a variety of motor with brake, belt speed reducer.
And then, because of its compliance with international standards, in the world can be assured that the use of.
Smooth running, there is a very seasonal rate of observation and control,
The speed fluctuation of the motor is greatly reduced, and the speed of the motor can be smoothly operatedServo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the controll circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDV-1R9D25A.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGDV-1R9D25A.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control

...More relevant models >>>>