SGDV-1R6A25A Servo driver for linear servo motor

YaskawaServo driver for linear servo motorSGDV-1R6A25A

SGDV-1R6A25A Introduce | SGDV-1R6A25A Catalog / Manual / Instructions / Software download

Yaskawa SGDV-1R6A25A Product information and technical parameters：
Brand: Yaskawa
Name: Servo driver for linear servo motor
Model: SGDV-1R6A25A
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.

Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit delta.
Rated speed: 800r/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC24V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGDV-1R6A25A SGDV-1R6A25A
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r/min and 1500r/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen SGDV-1R6A25A.

Full closed loop module.
Maximum applicable motor capacity: 11kw.
Power supply voltage: three phase AC400V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard) SGDV-1R6A25A.
Optional modules: full closed loop module.
Full closed loop control system is used to control the rotating servo motor.
Please install the servo unit.
Using the position feedback signal which is output by the external encoder (linear grating ruler) installed on the side of the machine to realize the high precision and high response.
External encoder capable of corresponding high resolution (linear grating). High performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 0.75kw.
Power supply voltage: single phase AC100V.
Design sequence: A.
Hardware specification: base mounting type (standard).
Interface: MECHATROLINK-III communication command type (linear servo motor).
Function: support 125 s communication cycle.
High performance sigma shaped -V-EX series.
2 models of high performance sservo unit SGDV-1R6A25A.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved. SGDV-1R6A25A.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control.

...More relevant models >>>>