Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDH series
>> SGDH-01AE High performance servo driver
SGDH-01AE High performance servo driver
Yaskawa SGDH-01AE Manual And Instructions
SGDH-01AE datasheetPDF datasheet
SGDH-01AE AC Servodrive (400 V, 22 to 55 kW) Installation Guide
SGDH-01AE Instruction Guide
Yaskawa SGDH-01AE Product information and technical parameters：
Brand: Yaskawa
Name: High performance servo driver
Model: SGDH-01AE
Type: SGDH type drive.
Capacity: 0.1kw.
Voltage: single phase 200V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data.
...More relevant models >>>>
SGDH-01AE datasheetPDF datasheet
SGDH-01AE AC Servodrive (400 V, 22 to 55 kW) Installation Guide
SGDH-01AE Instruction Guide
Yaskawa SGDH-01AE Product information and technical parameters：
Brand: Yaskawa
Name: High performance servo driver
Model: SGDH-01AE
Type: SGDH type drive.
Capacity: 0.1kw.
Voltage: single phase 200V.
Mode: torque, speed, position.
Test platform for mutual feedback of servo driver and motor.
Test platform with adjustable analog load.
A test platform with an actuator that has no load is used.
Test platform for driving the inherent load by using motor.
Test platform using on line test method.
This test system is composed of three parts,
Were measured servo driver - motor system, the system inherent load and host computer.
The host computer sends the speed command signal to the servo driver, and the servo system starts to run according to the instruction.
In the course of operation, the running data of the servo system is collected by the host computer and the data acquisition circuit,
And carries on the preservation, the analysis and the display to the data.
Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Optional (hardware): DB resistance external type.
Excellent mechanical properties, do the best in the master!
Easy and efficient work, is no longer a dream,
Sigma -v series servo drive, you can make your dreams come true SGDH-01AE SGDH-01AE
Sigma -v series is equipped with new free adjustment function,
Broke the common sense of the servo drive "can''t run smoothly without adjusting",
To achieve a pass that is to use.
A new type of advanced automatic tuning function Sigma -v series,
The installation time can be shortened, and the performance of the machine can be fully played SGDH-01AE. Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed) SGDH-01AE.
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 2.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the conttrol circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDH-01AE.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGDH-01AE.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
Maximum applicable motor capacity: 1.5kw.
Power supply voltage: three phase AC400V.
Design sequence: A type.
Interface: analog voltage, pulse sequence type (linear servo motor).
Optional (hardware): DB resistance external type.
Excellent mechanical properties, do the best in the master!
Easy and efficient work, is no longer a dream,
Sigma -v series servo drive, you can make your dreams come true SGDH-01AE SGDH-01AE
Sigma -v series is equipped with new free adjustment function,
Broke the common sense of the servo drive "can''t run smoothly without adjusting",
To achieve a pass that is to use.
A new type of advanced automatic tuning function Sigma -v series,
The installation time can be shortened, and the performance of the machine can be fully played SGDH-01AE. Sigma -V series servo motor SGMGV.
Rated output: 850W (0.85kw).
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal, with the brake (DC24V).
A variety of mechanical feed shaft drive (high speed feed) SGDH-01AE.
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 2.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: B.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the conttrol circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGDH-01AE.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number tthan the original product reduced by 1\/2 SGDH-01AE.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed control
...More relevant models >>>>
Last one: Yaskawa High performance servo driver SGDH-A5AE
next one: Yaskawa High performance servo driver SGDH-02AE
Related download