Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDM series
>> SGMSH type motor
>> SGMSH-50ACA31 Super high power motor
SGMSH-50ACA31 Super high power motor
Yaskawa SGMSH-50ACA31 Product information and technical parameters：
Brand: Yaskawa
Name: Super high power motor
Model: SGMSH-50ACA31
Servo motor SGMSH type.
Rated speed: 3000r\/min.
Power: 5.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: A.
Shaft end: taper 1\/10, with parallel key.
Optional parts: no brake oil seal.
Ultra high power response series: the need for small inertia, high torque.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic identification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters.
Standard for regenerative resistance connection terminals.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor
Sigma -V series servo motor SGMAV.
Rated output: 0.15kw (150W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%) SGMSH-50ACA31.
Equipped with a high resolution serial encoder (20 bit) SGMSH-50ACA31
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15 SGMSH-50ACA31.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection SGMSH-50ACA31.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationSingle axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suppression function.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth driveHigh performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specification: rack mounting type.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Function: support 125 s communication cycle.
High performance sigma shaped -V-EX series.
2 models of high performance seervo unit SGMSH-50ACA31.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved. SGMSH-50ACA31.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control.
Rated output: 0.15kw (150W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%) SGMSH-50ACA31.
Equipped with a high resolution serial encoder (20 bit) SGMSH-50ACA31
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15 SGMSH-50ACA31.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection SGMSH-50ACA31.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationSingle axis servo driver SGD7S.
Maximum applicable motor capacity: 0.4kW.
Voltage: single phase \/ three phase AC200V.
Interface: MECHATROLINK-III communication command type (Chinese market is RJ-45 connector). ఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problem.
Single axis servo unit.
Speed frequency response 3.1kHz.
Best use: in order to release the EX\/FT specifications.
Vibration suppression function.
For the inability to improve the speed loop gain of the machine,
Can reduce the velocity fluctuation by cogging motor.
Smooth driveHigh performance, use the best type of servo unit (high performance).
Maximum applicable motor capacity: 15kw.
Power supply voltage: three phase AC200V.
Design sequence: A.
Hardware specification: rack mounting type.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Function: support 125 s communication cycle.
High performance sigma shaped -V-EX series.
2 models of high performance seervo unit SGMSH-50ACA31.
EX001 (support M- III high speed communication): the communication cycle is the minimum value of 125 s, which makes the response of the instruction becomes faster, and the track accuracy and processing ability are improved. SGMSH-50ACA31.
EX002 (no deviation of the specification): greatly improve the command tracking performance, and further improve the accuracy of trajectory control.
...More relevant models >>>>
Last one: Yaskawa Super high power motor SGMSH-40ACA31
next one: Yaskawa Super high power motor SGMSH-10ACA3S
Related download